Another project done!
-
- Posts: 7158
- Joined: Thu May 07, 2020 7:57 pm
Re: Another project done!
We don't pay at our tip Ray its free.
Bernie.
Bernie.
- Greynomad
- Posts: 8029
- Joined: Tue Dec 04, 2012 4:16 pm
- Location: Rutherglen, Vic.
Re: Another project done!
Bernie,
Still better to make a few dollars from them rather than throw them away…
Fb Buy, Swap, Sell ads are free!
Still better to make a few dollars from them rather than throw them away…
Fb Buy, Swap, Sell ads are free!
Regards & God bless,
Ray
--
"Insufficient data for a meaningful answer."
Isaac Asimov, "The Last Question"
"I refuse to drink water, because of the disgusting things fish do in it"
W.C.Fields
Ray
--
"Insufficient data for a meaningful answer."
Isaac Asimov, "The Last Question"
"I refuse to drink water, because of the disgusting things fish do in it"
W.C.Fields
- Greynomad
- Posts: 8029
- Joined: Tue Dec 04, 2012 4:16 pm
- Location: Rutherglen, Vic.
Re: Another project done!
I just knew it wouldn’t be the last garden bed!
Marked out — with revisions — ready to remove the grass and start soil conditioning.
Another one going in around one of our water tanks.Marked out — with revisions — ready to remove the grass and start soil conditioning.
You do not have the required permissions to view the files attached to this post.
Regards & God bless,
Ray
--
"Insufficient data for a meaningful answer."
Isaac Asimov, "The Last Question"
"I refuse to drink water, because of the disgusting things fish do in it"
W.C.Fields
Ray
--
"Insufficient data for a meaningful answer."
Isaac Asimov, "The Last Question"
"I refuse to drink water, because of the disgusting things fish do in it"
W.C.Fields
- Dot
- Posts: 23557
- Joined: Fri Nov 23, 2012 6:12 pm
- Location: Strathalbyn SA
Re: Another project done!
Good one Joy keep him busy
Queen of the Banal & OT chatter and proud of it. If it offends you then tough titty titty bang bang.
- Greynomad
- Posts: 8029
- Joined: Tue Dec 04, 2012 4:16 pm
- Location: Rutherglen, Vic.
Re: Another project done!
Border complete, irises in.
More border strips to be purchased today to follow the tank wall contour.
Then, after grass is chipped out, we’ll fill the part covered by black plastic with driveway gravel (need access to the pump, against the wall), & finish the planting on the right.
More border strips to be purchased today to follow the tank wall contour.
Then, after grass is chipped out, we’ll fill the part covered by black plastic with driveway gravel (need access to the pump, against the wall), & finish the planting on the right.
You do not have the required permissions to view the files attached to this post.
Regards & God bless,
Ray
--
"Insufficient data for a meaningful answer."
Isaac Asimov, "The Last Question"
"I refuse to drink water, because of the disgusting things fish do in it"
W.C.Fields
Ray
--
"Insufficient data for a meaningful answer."
Isaac Asimov, "The Last Question"
"I refuse to drink water, because of the disgusting things fish do in it"
W.C.Fields
-
- Posts: 7158
- Joined: Thu May 07, 2020 7:57 pm
Re: Another project done!
Where are you getting the edging from Ray.
Bernie.
Bernie.
- Greynomad
- Posts: 8029
- Joined: Tue Dec 04, 2012 4:16 pm
- Location: Rutherglen, Vic.
Re: Another project done!
Peards Garden Supplies in Albury sell Corten steel edging in 2.4m lengths and various widths (ours are 100mm).
Can’t remember the brand name.
The top is rolled to form a 10mm lip. Joiners are simply a short piece of the same, inverted so the lip of the joiner locks the bottom edge, and the ‘bottom’ edge slips into the lip at the top. All fixed together with 12mm self-tapping hex-head screws (supplied). Also supplied are 300mm flat steel pegs (which also fit inside the lip) to locate the edging.
The 2.4m lengths can be gently bent to whatever curve you need, as I have on the “Final” garden bed and the new tank surround. Check out the last two sets of garden pics… you can see in the pic of the western part of the “Final” bed just how tight a curve you can get. But it needs care to bend it without kinking it. I’ll take some detail pics tomorrow.
Meantime, here’s a detailed pic of the “odds & sods”: Screws (lots!); joiner (100x100mm); 300mm peg/spike.
The only difference between the joiner & the edging is that the edging is 100mm x 2.4m. Close-up showing the rolled top of the joiner.
Obviously the spike is driven into the ground until only 100mm is showing, and the 2.4m edging piece is slipped over it so the spike sits inside the rolled top, then it’s secured in place with a hex-head screw. Arguably the screw is redundant, but I’m a ‘belt & braces’ guy…
I place spikes at every joint and the mid-point of each length, meaning there’s a locating spike every 1.2m.
I also pre-drill a 3.5mm hole for the 4mm screws… quality variations in the steel of the self-tapping screws means they sometimes don’t ‘self’.
Can’t remember the brand name.
The top is rolled to form a 10mm lip. Joiners are simply a short piece of the same, inverted so the lip of the joiner locks the bottom edge, and the ‘bottom’ edge slips into the lip at the top. All fixed together with 12mm self-tapping hex-head screws (supplied). Also supplied are 300mm flat steel pegs (which also fit inside the lip) to locate the edging.
The 2.4m lengths can be gently bent to whatever curve you need, as I have on the “Final” garden bed and the new tank surround. Check out the last two sets of garden pics… you can see in the pic of the western part of the “Final” bed just how tight a curve you can get. But it needs care to bend it without kinking it. I’ll take some detail pics tomorrow.
Meantime, here’s a detailed pic of the “odds & sods”: Screws (lots!); joiner (100x100mm); 300mm peg/spike.
The only difference between the joiner & the edging is that the edging is 100mm x 2.4m. Close-up showing the rolled top of the joiner.
Obviously the spike is driven into the ground until only 100mm is showing, and the 2.4m edging piece is slipped over it so the spike sits inside the rolled top, then it’s secured in place with a hex-head screw. Arguably the screw is redundant, but I’m a ‘belt & braces’ guy…
I place spikes at every joint and the mid-point of each length, meaning there’s a locating spike every 1.2m.
I also pre-drill a 3.5mm hole for the 4mm screws… quality variations in the steel of the self-tapping screws means they sometimes don’t ‘self’.
You do not have the required permissions to view the files attached to this post.
Regards & God bless,
Ray
--
"Insufficient data for a meaningful answer."
Isaac Asimov, "The Last Question"
"I refuse to drink water, because of the disgusting things fish do in it"
W.C.Fields
Ray
--
"Insufficient data for a meaningful answer."
Isaac Asimov, "The Last Question"
"I refuse to drink water, because of the disgusting things fish do in it"
W.C.Fields
-
- Posts: 7158
- Joined: Thu May 07, 2020 7:57 pm
Re: Another project done!
Thanks for that.
Bernie.
Bernie.
- Greynomad
- Posts: 8029
- Joined: Tue Dec 04, 2012 4:16 pm
- Location: Rutherglen, Vic.
Re: Another project done!
Bernie,
Some detail pix of borders in use. Nice & shiny, as purchased on Friday. Surface after a month of weathering.
You can see the lip of the joiner at the bottom, with the securing screws holding the two lengths together. Inside the same joint. I doubled up, putting the stake on the joining screws. It won’t fit inside the rolled top with the joiner, so I hammered it into the ground a further 10mm so it sits flush. This is the inside view of a stake midway on a length of the edging.
Some detail pix of borders in use. Nice & shiny, as purchased on Friday. Surface after a month of weathering.
You can see the lip of the joiner at the bottom, with the securing screws holding the two lengths together. Inside the same joint. I doubled up, putting the stake on the joining screws. It won’t fit inside the rolled top with the joiner, so I hammered it into the ground a further 10mm so it sits flush. This is the inside view of a stake midway on a length of the edging.
You do not have the required permissions to view the files attached to this post.
Regards & God bless,
Ray
--
"Insufficient data for a meaningful answer."
Isaac Asimov, "The Last Question"
"I refuse to drink water, because of the disgusting things fish do in it"
W.C.Fields
Ray
--
"Insufficient data for a meaningful answer."
Isaac Asimov, "The Last Question"
"I refuse to drink water, because of the disgusting things fish do in it"
W.C.Fields
-
- Posts: 7158
- Joined: Thu May 07, 2020 7:57 pm
Re: Another project done!
Looks good Ray...I hadn't seen steel garden edging before.
Bernie.
Bernie.