Page 2176 of 2614

Re: Good morning daily

Posted: Thu Oct 10, 2024 12:22 pm
by T1 Terry
Helen Grose wrote: Thu Oct 10, 2024 11:58 am Dots been busy
I think she might be have a caesarean section, the legs are out already :lol: good to see she has this one on a lead already ;)

T1 Terry

Re: Good morning daily

Posted: Thu Oct 10, 2024 6:00 pm
by supersparky
Looks like wind to me. :lol: :lol:
She's well known for it. :lol:
It's not a lead, it's a tether to stop her from drifting away.

Re: Good morning daily

Posted: Thu Oct 10, 2024 6:07 pm
by jon_d
It's not a lead, it's a tether to stop her from drifting away.
Dave, do you mean like in space when a retro rocket fires?

Re: Good morning daily

Posted: Thu Oct 10, 2024 6:58 pm
by supersparky
No, I mean like in space, or like in Willy Wonka where they just float away.
Come back Dot and Helen, we still love you. :lol: :lol: :lol:

Re: Good morning daily

Posted: Thu Oct 10, 2024 7:23 pm
by jon_d
There is a good thing about farting in space... no one can hear you.

Re: Good morning daily

Posted: Thu Oct 10, 2024 7:28 pm
by supersparky
jon_d wrote: Thu Oct 10, 2024 7:23 pm There is a good thing about farting in space... no one can hear you.
:lol: :lol: :lol: Yes, well, there is that small mercy, I suppose. Thank goodness. :lol:

Re: Good morning daily

Posted: Thu Oct 10, 2024 7:44 pm
by BernieQ2
jon_d wrote: Thu Oct 10, 2024 7:23 pm There is a good thing about farting in space... no one can hear you.
Depending on the space... elevator comes to mind 😁

Re: Good morning daily

Posted: Thu Oct 10, 2024 9:45 pm
by jon_d
Space the place, Bernie. ;)


Terry, what's the update?

Re: Good morning daily

Posted: Thu Oct 10, 2024 10:11 pm
by T1 Terry
Still trying to get No:1 inlet to seal, the crap on the valve face/seat seems to be on the edges hidden by the angle of the inlet port ..... another try tomorrow. Fixed the valve clearance problems, so now have full compression in No:3 cyl. Ground down the lower edge of upper piston in the hydraulic lifter to get enough clearance to get a bit of movement in the hydraulic lifter when depressing it while the cam lobe was up .... when the valve should be fully closed. I had to do both lifters on No:3 cyl and the inlet on No:1 cyl, and removed a lot more than I expected I'd need to, but that was probably more to do with ratio of the rocker arm length each side of the cam lobe .....
So, I'm happy with today's progress, depends how much of Bathurst is shown on the 'puter as to how much I get done tomorrow

T1 Terry

Re: Good morning daily

Posted: Fri Oct 11, 2024 6:25 am
by BernieQ2
Good morning.
It numberfies (new word) me how the medical profession works... Carol sat for one and a half hour's yesterday...to be told the person she had appointment with.... didn't come to work....🤬🤬
So after that sharmosill (another new word) we went to maryborough for her appointment with the hearing test...at least they were there..
It turns out the doctor who wanted her to have the test was right... she has a disease in her ear that is giving her the vertigo... treatable but not fixable 😡. So I'm not sure if we had one win or two losses for the day...
And a trip to Bunnings for some needed goodies on the way home.
We encountered rain on the way home... nothing here..
I haven't been to your space Jon, but have been in a elevator 😁
Keep safe.
Bernie.
Almost forgot it was miss Olivia's 17th birthday yesterday we did ring her before she went to school... and will be having lunch with her next Sunday.