Page 97 of 123
Re: Bernie and Carols Isuzu fit out.
Posted: Thu Jun 15, 2017 4:09 pm
by BernieQ2
Another problem for you smart folks to help with I have this watt meter (pic supplied) some one has lost the paper work?
have had it for a few years . So how does one hook this up ? It has as you can see a red wire a black wire a yellow wire and lastly a white wire . Anyone have knowledge of these beasts .
Bernie .
DSCF2660 (Custom).JPG
DSCF2659 (Custom).JPG
Re: Bernie and Carols Isuzu fit out.
Posted: Thu Jun 15, 2017 4:28 pm
by BruceS
Looks a bit like this one?
http://www.ebay.com.au/itm/DC-6-5-100V- ... qulHK7zU8g
I reckon it needs a shunt.
Re: Bernie and Carols Isuzu fit out.
Posted: Thu Jun 15, 2017 7:48 pm
by jon_d
red and black are power the the device.
white and yellow across the shunt.
Re: Bernie and Carols Isuzu fit out.
Posted: Thu Jun 15, 2017 7:57 pm
by BernieQ2
Thanks Bruce and Jon , I think the shunt I had went into the Civilian when I had it , but will fossick around in the shed and see what I may find .
Bernie .
Re: Bernie and Carols Isuzu fit out.
Posted: Sat Jul 15, 2017 10:53 am
by BernieQ2
Ok here we go again . My engine air compressor is more like a oil pump , so I have bought a new one to replace the old one .
First pic bus up a bit higher it will have the driver's wheel removed and will be sitting on stands . The second pic is the new air compressor and the third pic is where the old one is and new to go ....If I get my pics in order that is .
Bernie .
DSCF2722 (Custom).JPG
DSCF2720 (Custom).JPG
DSCF2721 (Custom).JPG
Re: Bernie and Carols Isuzu fit out.
Posted: Sat Jul 15, 2017 11:29 am
by BruceS
Oh!! Please do NOT swear when doing THAT job Bernie!!
Where does it suck air from Bernie? From the air cleaner or from the tappet cover? My old Bedford originally had it on the breather on the cover & it sucked crap in from there.
That hose almost looks like it has been sucking flat? (or out of shape?)
The one with the green stripe on it. If so, then it might help suck oil past the rings?
Re: Bernie and Carols Isuzu fit out.
Posted: Sat Jul 15, 2017 12:20 pm
by BernieQ2
Yes Bruce will renew all those hoses . I'm going to need a 54mm socket to remove the harmonic balancer....bloody big mongrel .
It sucks from the air cleaner . That's the incoming hose .
Bernie .
Re: Bernie and Carols Isuzu fit out.
Posted: Sat Jul 15, 2017 12:57 pm
by BruceS
Why remove the harmonic balancer Bernie? Has leaking oil wrecked the rubber?
The compressor should pop out once you undo the 4 studs.... won't it?
PS. I'll check if I have that sized socket. Do you have a 3/4" drive breaker bar?
Re: Bernie and Carols Isuzu fit out.
Posted: Sat Jul 15, 2017 1:04 pm
by BruceS
Only got 1 7/16" & 1 3/8" here on the boat.
I think I got a couple of others in storage.
You need 54mm or 2 1/8" ??
Re: Bernie and Carols Isuzu fit out.
Posted: Sat Jul 15, 2017 1:40 pm
by BernieQ2
The manual says 54mm Bruce . The bolts that hold the compressor are inside the front engine cover.
Bernie .