Flywheel
-
jon_d
- Posts: 4676
- Joined: Thu Apr 11, 2013 6:37 pm
- Location: bedford
- Has thanked: 42 times
- Been thanked: 36 times
Re: Flywheel
Wayne,
please make sure the flywheel is balanced and then the new clutch pressure plate is balanced.
I balanced the Isuzu's flywheel and pressure plate. It's amazing the difference in smoothness it makes.
please make sure the flywheel is balanced and then the new clutch pressure plate is balanced.
I balanced the Isuzu's flywheel and pressure plate. It's amazing the difference in smoothness it makes.
-
T1 Terry
- Posts: 15963
- Joined: Fri Nov 23, 2012 3:44 pm
- Location: Mannum South Australia by the beautiful Murray River
- Has thanked: 50 times
- Been thanked: 30 times
Re: Flywheel
Have they found a new method of attaching it to the crankshaft and attaching the pressure plate?
A person may fail many times, they only become a failure when they blame someone else John Burrows
Those who struggle to become a leader, rarely know a clear direction forward for anyone but themselves
Those who struggle to become a leader, rarely know a clear direction forward for anyone but themselves
-
BruceS
- Site Admin
- Posts: 9304
- Joined: Thu Nov 22, 2012 7:32 pm
- Location: Mannum, SA, 5238
- Has thanked: 36 times
- Been thanked: 36 times
Re: Flywheel
haha ... also make sure they put a ring gear on Wayne!!! A bit hard to start otherwise!
Was the old ring gear OK? Maybe move it several degrees so it engages in a 'new' area.
I would think they would know enough to have the new clutch plate & pressure plate at the shop & balance it all as a unit.
I bet you are getting a bit keen to get moving by now?
No more slipping the clutch to back into tight spots!!!
EDIT: welding it Terry? lol
Was the old ring gear OK? Maybe move it several degrees so it engages in a 'new' area.
I would think they would know enough to have the new clutch plate & pressure plate at the shop & balance it all as a unit.
I bet you are getting a bit keen to get moving by now?
No more slipping the clutch to back into tight spots!!!
EDIT: welding it Terry? lol
*******************
BruceS
Mannum, SA
********************
BruceS
Mannum, SA
********************
-
jon_d
- Posts: 4676
- Joined: Thu Apr 11, 2013 6:37 pm
- Location: bedford
- Has thanked: 42 times
- Been thanked: 36 times
Re: Flywheel
The flywheel has to be balanced individually. Then, the pressure plate can be added and balanced.I would think they would know enough to have the new clutch plate & pressure plate at the shop & balance it all as a unit.
If they are balanced as one, then the balance will be lost if the pressure plate is replaced.
-
Mrcoolabah1au
- Posts: 2699
- Joined: Wed Jan 23, 2013 3:36 pm
- Location: Tocumwal on the Murray river
-
T1 Terry
- Posts: 15963
- Joined: Fri Nov 23, 2012 3:44 pm
- Location: Mannum South Australia by the beautiful Murray River
- Has thanked: 50 times
- Been thanked: 30 times
Re: Flywheel
A big ask these days, the off grid solar system we recently finished upgrading was last installed by a supposed "off grid solar expert" and wasn't even close to being anywhere near the requirements as far as choice of cabling, cable size and separation between 240vac cabling and 48v cabling. We made the error of assuming the last people knew what they were doing and we could just link into the cabling they had used, so our quoted install time was not even close to the time it actually took and that threw out our costing and work scheduling.
A person may fail many times, they only become a failure when they blame someone else John Burrows
Those who struggle to become a leader, rarely know a clear direction forward for anyone but themselves
Those who struggle to become a leader, rarely know a clear direction forward for anyone but themselves
-
Mrcoolabah1au
- Posts: 2699
- Joined: Wed Jan 23, 2013 3:36 pm
- Location: Tocumwal on the Murray river
Re: Flywheel
Yes ok the only custom made flywheel in Australia ready to be fitted seen it first hand today 
You do not have the required permissions to view the files attached to this post.
Coolabah1au
Wayne nini
Wayne nini
-
Mrcoolabah1au
- Posts: 2699
- Joined: Wed Jan 23, 2013 3:36 pm
- Location: Tocumwal on the Murray river
Re: Flywheel
Just got word that the bus is all back together so everything is working well 
will be nice Christmas present 
will be nice Christmas present 
Coolabah1au
Wayne nini
Wayne nini