Torque socket
-
Dot
- Posts: 25112
- Joined: Fri Nov 23, 2012 6:12 pm
- Location: Strathalbyn SA
- Has thanked: 15 times
- Been thanked: 101 times
Re: Torque socket
Hello !!!
Queen of the Banal & OT chatter and proud of it. If it offends you then tough titty titty bang bang.
-
T1 Terry
- Posts: 16810
- Joined: Fri Nov 23, 2012 3:44 pm
- Location: Mannum South Australia by the beautiful Murray River
- Has thanked: 95 times
- Been thanked: 81 times
Re: Torque socket
Hello Dottie
I know the set-up Bruce is trying to work with and a deeper socket will not work with the torque multiplier to undo the wheel nuts, it would push the leg on the torque multiplier too far out and it wouldn't engage against the other wheel studs .... Hard to make a picture with words, but the nut assembly that holds the inside wheel on has a 21mm square drive on the end and threaded on the outside. The outer wheel goes over that nut assembly and a much bigger nut (41mm) tightens the outer wheel onto that nut/stud. The 41mm socket Bruce has, doesn't have a hole through the centre big enough for the nut/stud to fit through, so he needs to make the hole in the centre bigger by not a lot ....
T1 Terry
A person may fail many times, they only become a failure when they blame someone else John Burrows
Those who struggle to become a leader, rarely know a clear direction forward for anyone but themselves
Those who struggle to become a leader, rarely know a clear direction forward for anyone but themselves
-
BruceS
- Site Admin
- Posts: 9482
- Joined: Thu Nov 22, 2012 7:32 pm
- Location: Nebo, Qld
- Has thanked: 76 times
- Been thanked: 69 times
Re: Torque socket
Sackly! Got it in one!
It's not essential but a work in progress.
It's not essential but a work in progress.
*******************
BruceS
Nebo, Qld
********************
BruceS
Nebo, Qld
********************
-
BruceS
- Site Admin
- Posts: 9482
- Joined: Thu Nov 22, 2012 7:32 pm
- Location: Nebo, Qld
- Has thanked: 76 times
- Been thanked: 69 times
Re: Torque socket
Met a chap by accident from here & asked if he knew someone in town that might have the capability to enlarge the centre hole. He said give it to me
, nothing will stop me. He rebuilds, renovates huge mining equip.
, nothing will stop me. He rebuilds, renovates huge mining equip.
*******************
BruceS
Nebo, Qld
********************
BruceS
Nebo, Qld
********************
-
T1 Terry
- Posts: 16810
- Joined: Fri Nov 23, 2012 3:44 pm
- Location: Mannum South Australia by the beautiful Murray River
- Has thanked: 95 times
- Been thanked: 81 times
Re: Torque socket
Now that sounds like a better solution
T1 Terry
A person may fail many times, they only become a failure when they blame someone else John Burrows
Those who struggle to become a leader, rarely know a clear direction forward for anyone but themselves
Those who struggle to become a leader, rarely know a clear direction forward for anyone but themselves
-
BruceS
- Site Admin
- Posts: 9482
- Joined: Thu Nov 22, 2012 7:32 pm
- Location: Nebo, Qld
- Has thanked: 76 times
- Been thanked: 69 times
Re: Torque socket
Job done. What a legend!
*******************
BruceS
Nebo, Qld
********************
BruceS
Nebo, Qld
********************