can anyone tell how or if possible to start an equalisation charge on a PL. I have 3 Batteries I want to equalise separately but cannot find how to force the mode into operation.
Craig
PL 40 equalisation mode
-
Craig
- Posts: 774
- Joined: Fri Dec 14, 2012 9:28 pm
- Location: on the east coast.
-
Craig
- Posts: 774
- Joined: Fri Dec 14, 2012 9:28 pm
- Location: on the east coast.
Re: PL 40 equalisation mode
If I don't respond it is due to little (if any most of the time) internet signal where we are at the moment.
Craig
Craig
Full time on the road in an Alpine 2855
-
Shirley
- Posts: 4555
- Joined: Sat Dec 29, 2012 4:06 pm
- Location: Lake Macquarie. NSW.
- Has thanked: 15 times
- Been thanked: 26 times
Re: PL 40 equalisation mode
We have the manual on the PL, Would you like me to send you the section on equalisation?
Shirley & Bruce.
-
Newcastle George
- Posts: 3284
- Joined: Wed Dec 05, 2012 3:21 pm
- Location: Kotara, Newcastle
- Has thanked: 2 times
- Been thanked: 8 times
Re: PL 40 equalisation mode
If it is the same as the Dingo, press and hold button when BatV is showing and do the same with Boost and Float until Equal shows.
Hope this helps.
The manual page 6 should assist.
George
Hope this helps.
The manual page 6 should assist.
George
George, Julie, Leonie & Sean - Kotara, Newcastle
DIY 11.5M 1979 Bedford, Nissan/UD FE6T motor
DIY 11.5M 1979 Bedford, Nissan/UD FE6T motor
-
T1 Terry
- Posts: 15964
- Joined: Fri Nov 23, 2012 3:44 pm
- Location: Mannum South Australia by the beautiful Murray River
- Has thanked: 50 times
- Been thanked: 30 times
Re: PL 40 equalisation mode
George has it, press and hold in the battery voltage window on the normal menu and you can force the unit into the next mode of charging, a short push returns it to the standard menu.
To adjust the different charge setting, long push on set, short pushes ensuring program 4 is still selected and scroll through to REG, long push and this opens the charging settings, 1st setting is boost voltage 2nd is equalise voltage, 3rd is equalise duration and 4th is equalise frequency. If equalise frequency is set to zero there will be no equalise mode available in the scrolling voltage menu.
To adjust the different charge setting, long push on set, short pushes ensuring program 4 is still selected and scroll through to REG, long push and this opens the charging settings, 1st setting is boost voltage 2nd is equalise voltage, 3rd is equalise duration and 4th is equalise frequency. If equalise frequency is set to zero there will be no equalise mode available in the scrolling voltage menu.
A person may fail many times, they only become a failure when they blame someone else John Burrows
Those who struggle to become a leader, rarely know a clear direction forward for anyone but themselves
Those who struggle to become a leader, rarely know a clear direction forward for anyone but themselves
-
Shirley
- Posts: 4555
- Joined: Sat Dec 29, 2012 4:06 pm
- Location: Lake Macquarie. NSW.
- Has thanked: 15 times
- Been thanked: 26 times
Re: PL 40 equalisation mode
George are you referring to page 6 of the user guide or the Reference Manual?
Shirley & Bruce.
-
Newcastle George
- Posts: 3284
- Joined: Wed Dec 05, 2012 3:21 pm
- Location: Kotara, Newcastle
- Has thanked: 2 times
- Been thanked: 8 times
Re: PL 40 equalisation mode
User Guide which the link refers to, Shirley.
George
George
George, Julie, Leonie & Sean - Kotara, Newcastle
DIY 11.5M 1979 Bedford, Nissan/UD FE6T motor
DIY 11.5M 1979 Bedford, Nissan/UD FE6T motor
-
shonky
- Posts: 636
- Joined: Tue Dec 25, 2012 10:31 am
Re: PL 40 equalisation mode
Hi, all.
Craig - go for 00 cables as well.
Craig - go for 00 cables as well.
See you on the back roads,
shonky et al.
shonky et al.
-
Craig
- Posts: 774
- Joined: Fri Dec 14, 2012 9:28 pm
- Location: on the east coast.
Re: PL 40 equalisation mode
Thanks Shirley but I have a manual. Unless yours is different to mine I couldn't find any information on how to force it into equalisation mode.
Thanks George but I had already tried that. I'm guessing that as equalisation normally starts from 9am it must not give the option to push it into start. I will give it another go when the sun starts shinning again.
Sonky, why would I want to do that? The system has been in use for about 15 years now. Too late to worry about what size cable to fit
Thanks George but I had already tried that. I'm guessing that as equalisation normally starts from 9am it must not give the option to push it into start. I will give it another go when the sun starts shinning again.
Sonky, why would I want to do that? The system has been in use for about 15 years now. Too late to worry about what size cable to fit
Full time on the road in an Alpine 2855
-
shonky
- Posts: 636
- Joined: Tue Dec 25, 2012 10:31 am
Re: PL 40 equalisation mode
Hi, all.
Craig - fair enough. I've always found Brett at Brett's Camper Care in Clontarf to be very good on Plasmatronics, BTW.
Craig - fair enough. I've always found Brett at Brett's Camper Care in Clontarf to be very good on Plasmatronics, BTW.
See you on the back roads,
shonky et al.
shonky et al.