Left hand thread Bernie? Nah!
Haven't seen anything in the manual Bruce to say left hand .
Does say to lock the ring gear ?
Bernie .
Bernie and Carols Isuzu fit out.
-
- Posts: 15972
- Joined: Fri Nov 23, 2012 3:44 pm
- Location: Mannum South Australia by the beautiful Murray River
- Has thanked: 51 times
- Been thanked: 30 times
Re: Bernie and Carols Isuzu fit out.
Checked through the sockets just in case but no 54mm x 1"drive unfortunately. Certainly work ringing around the hire mobs to see if they have a 54mm x 1"drive, they sure won't be cheap to buy.
T1 Terry
A person may fail many times, they only become a failure when they blame someone else John Burrows
Those who struggle to become a leader, rarely know a clear direction forward for anyone but themselves
Those who struggle to become a leader, rarely know a clear direction forward for anyone but themselves
-
- Posts: 15972
- Joined: Fri Nov 23, 2012 3:44 pm
- Location: Mannum South Australia by the beautiful Murray River
- Has thanked: 51 times
- Been thanked: 30 times
Re: Bernie and Carols Isuzu fit out.
Don't be tempted to use a rattle gun, the gearset will be permanently damaged from the chattering involved at that torque and I doubt anything smaller than an 1"drive gun would shift it anyway.
A person may fail many times, they only become a failure when they blame someone else John Burrows
Those who struggle to become a leader, rarely know a clear direction forward for anyone but themselves
Those who struggle to become a leader, rarely know a clear direction forward for anyone but themselves
-
- Site Admin
- Posts: 9305
- Joined: Thu Nov 22, 2012 7:32 pm
- Location: Mannum, SA, 5238
- Has thanked: 36 times
- Been thanked: 36 times
Re: Bernie and Carols Isuzu fit out.
$75 on Ebay.
Bernie how deep does the socket need to be? Is it a nut or bolt? Does the shaft stick out very far?
Bernie how deep does the socket need to be? Is it a nut or bolt? Does the shaft stick out very far?
*******************
BruceS
Mannum, SA
********************
BruceS
Mannum, SA
********************
Re: Bernie and Carols Isuzu fit out.
Let you know on Friday Bruce, not climbing under the bus now and will be out all day tomorrow.
-
- Posts: 261
- Joined: Wed Dec 05, 2012 6:53 pm
- Location: Christie Downs, SA
Re: Bernie and Carols Isuzu fit out.
Hi Bernie
I am pretty sure I have one in the bus, was going to have a look the other day when you mentioned it.
I bought mine of eBay from NSW while staying near Wangaratta and it took 10 days, at the same time I bought a diesel heater from England and it arrived in 4 days.
If I have one I could post it to you.
Regards Geoff
I am pretty sure I have one in the bus, was going to have a look the other day when you mentioned it.
I bought mine of eBay from NSW while staying near Wangaratta and it took 10 days, at the same time I bought a diesel heater from England and it arrived in 4 days.
If I have one I could post it to you.
Regards Geoff
-
- Posts: 4681
- Joined: Thu Apr 11, 2013 6:37 pm
- Location: bedford
- Has thanked: 43 times
- Been thanked: 37 times
Re: Bernie and Carols Isuzu fit out.
I wonder if it uses locktight too?
Bernie, get a big bar, and a hydualic jack. Lift the end of the bar up using the jack. This will turn the nut or lift the bus.

Bernie, get a big bar, and a hydualic jack. Lift the end of the bar up using the jack. This will turn the nut or lift the bus.
-
- Posts: 242
- Joined: Sat Jul 19, 2014 9:11 pm
- Location: Geraldton WA
Re: Bernie and Carols Isuzu fit out.
54mm is 2-1/8" (53.98mm) which may be easier to beg or borrow
3/4 Drive and Long Bar should do it OK 588nm is not all that tite
3/4 Drive and Long Bar should do it OK 588nm is not all that tite
