Bernie and Carols Isuzu fit out.
-
El Gringo
- Posts: 401
- Joined: Sat Dec 28, 2013 1:48 pm
- Location: Adelaide SA
- Has thanked: 8 times
Re: Bernie and Carols Isuzu fit out.
OK, well I reckon i would hit it with heaps of WD40 or similar, then hit the starter a couple of times, just to rock it back and forward like??
Bernie B
I plan to stop procrastinating tomorrow.
I plan to stop procrastinating tomorrow.
-
BruceS
- Site Admin
- Posts: 9305
- Joined: Thu Nov 22, 2012 7:32 pm
- Location: Mannum, SA, 5238
- Has thanked: 36 times
- Been thanked: 36 times
Re: Bernie and Carols Isuzu fit out.
Bernie is there a join on it at all? (centre bit)
It looks like the taperlock pulleys I've seen & used on irrigation pumps and engines.
Lots of penetrene & a piece of 3" pipe that fits just outside the taper bit & a few wacks with a sledge hammer might see it "pop".
Has to be square on with equal all around for it to let go.
On the ones I used there were 2 threaded holes for bolts through a plate over the centre shaft.
It may be different .... I can't see it as you can!
It looks like the taperlock pulleys I've seen & used on irrigation pumps and engines.
Lots of penetrene & a piece of 3" pipe that fits just outside the taper bit & a few wacks with a sledge hammer might see it "pop".
Has to be square on with equal all around for it to let go.
On the ones I used there were 2 threaded holes for bolts through a plate over the centre shaft.
It may be different .... I can't see it as you can!
*******************
BruceS
Mannum, SA
********************
BruceS
Mannum, SA
********************
Re: Bernie and Carols Isuzu fit out.
Eureka tiz out , I used wedges from behind and slowly it moved .
Bernie .
Now the fun can begin But unfortunately it just went beer O'clock .
Bernie .
Now the fun can begin But unfortunately it just went beer O'clock .
You do not have the required permissions to view the files attached to this post.
-
El Gringo
- Posts: 401
- Joined: Sat Dec 28, 2013 1:48 pm
- Location: Adelaide SA
- Has thanked: 8 times
Re: Bernie and Carols Isuzu fit out.
Good work Bernie... Only took all day.. 
Bernie B
I plan to stop procrastinating tomorrow.
I plan to stop procrastinating tomorrow.
-
Dot
- Posts: 24722
- Joined: Fri Nov 23, 2012 6:12 pm
- Location: Strathalbyn SA
- Been thanked: 37 times
Re: Bernie and Carols Isuzu fit out.
Quicker than our job, unable to even see the repairer until next Wednesday. 
Well done Bernie.
Well done Bernie.Queen of the Banal & OT chatter and proud of it. If it offends you then tough titty titty bang bang.
-
El Gringo
- Posts: 401
- Joined: Sat Dec 28, 2013 1:48 pm
- Location: Adelaide SA
- Has thanked: 8 times
Re: Bernie and Carols Isuzu fit out.
Well he's only taking bits off to get to the job so far...
If he's anything like me, by the time I've done the job I either can't find the bits that came off, or I can't remember how they go back on.
Cheers,
Bernie B
I plan to stop procrastinating tomorrow.
I plan to stop procrastinating tomorrow.
Re: Bernie and Carols Isuzu fit out.
Maybe I should give the reassembly to Carol, as she hasn't seen the unasembly should be a walk in the park?.
BernieQ.
BernieQ.
-
T1 Terry
- Posts: 15972
- Joined: Fri Nov 23, 2012 3:44 pm
- Location: Mannum South Australia by the beautiful Murray River
- Has thanked: 51 times
- Been thanked: 30 times
Re: Bernie and Carols Isuzu fit out.
I thought you were putting the feet up cause it was beer o'clock? Was there a square key as a locator or a half moon key in the shaft?
A person may fail many times, they only become a failure when they blame someone else John Burrows
Those who struggle to become a leader, rarely know a clear direction forward for anyone but themselves
Those who struggle to become a leader, rarely know a clear direction forward for anyone but themselves
Re: Bernie and Carols Isuzu fit out.
I haven't looked Terry , just harmonic balancer off then down tools.
Can't rush into what can be done at a later date.
Bernie.
Can't rush into what can be done at a later date.
Bernie.
-
jon_d
- Posts: 4680
- Joined: Thu Apr 11, 2013 6:37 pm
- Location: bedford
- Has thanked: 43 times
- Been thanked: 37 times
Re: Bernie and Carols Isuzu fit out.
Bernie
how tight was the nut?
Did you have a lot of trouble?
When assembling they say to use grease on the thread.
Terry, the manual sort of shows no key-way on the pulley. Just a key on the gear driving the timing gears.
how tight was the nut?
Did you have a lot of trouble?
When assembling they say to use grease on the thread.
Terry, the manual sort of shows no key-way on the pulley. Just a key on the gear driving the timing gears.