Bernie,
the part number for the timing case gasket is
Part 20-1
111322-0370
111322-0550
111322-0520
this is the right shape for the timing cover; not sure which number after that. The different numbers are for different OEM engines. (They must have made millions of them.)
Bernie and Carols Isuzu fit out.
-
BruceS
- Site Admin
- Posts: 9305
- Joined: Thu Nov 22, 2012 7:32 pm
- Location: Mannum, SA, 5238
- Has thanked: 36 times
- Been thanked: 36 times
Re: Bernie and Carols Isuzu fit out.
Jon,
Part 20-1
or
Page 20-1
?
Now where do I get my parts from? Brett's Trucks keep Iveco parts? Doesn't look like it on their website.
Part 20-1
or
Page 20-1
?
Now where do I get my parts from? Brett's Trucks keep Iveco parts? Doesn't look like it on their website.
*******************
BruceS
Mannum, SA
********************
BruceS
Mannum, SA
********************
-
bagmaker
- Posts: 886
- Joined: Sun Jan 20, 2013 4:56 pm
- Location: Victoria
-
BruceS
- Site Admin
- Posts: 9305
- Joined: Thu Nov 22, 2012 7:32 pm
- Location: Mannum, SA, 5238
- Has thanked: 36 times
- Been thanked: 36 times
Re: Bernie and Carols Isuzu fit out.
Thankyou. Once I get a list I'll contact a few & get prices.
*******************
BruceS
Mannum, SA
********************
BruceS
Mannum, SA
********************
-
jon_d
- Posts: 4681
- Joined: Thu Apr 11, 2013 6:37 pm
- Location: bedford
- Has thanked: 43 times
- Been thanked: 37 times
Re: Bernie and Carols Isuzu fit out.
20-1
You do not have the required permissions to view the files attached to this post.
-
Newcastle George
- Posts: 3285
- Joined: Wed Dec 05, 2012 3:21 pm
- Location: Kotara, Newcastle
- Has thanked: 2 times
- Been thanked: 8 times
Re: Bernie and Carols Isuzu fit out.
Bernie,
Here is a photo of the fuel adjustment screw on my injector pump that you asked about. Half a turn in or out makes a difference.
George
Click to enlarge
Here is a photo of the fuel adjustment screw on my injector pump that you asked about. Half a turn in or out makes a difference.
George
Click to enlarge
You do not have the required permissions to view the files attached to this post.
George, Julie, Leonie & Sean - Kotara, Newcastle
DIY 11.5M 1979 Bedford, Nissan/UD FE6T motor
DIY 11.5M 1979 Bedford, Nissan/UD FE6T motor
-
T1 Terry
- Posts: 15972
- Joined: Fri Nov 23, 2012 3:44 pm
- Location: Mannum South Australia by the beautiful Murray River
- Has thanked: 51 times
- Been thanked: 30 times
Re: Bernie and Carols Isuzu fit out.
Newcastle George wrote: ↑Wed Jul 26, 2017 4:49 pm Bernie,
Here is a photo of the fuel adjustment screw on my injector pump that you asked about. Half a turn in or out makes a difference.
George
Click to enlarge
100_3926 (Custom).JPG
Why didn't I see that when we were doing battle with it George? Is it well hidden below floor level
A person may fail many times, they only become a failure when they blame someone else John Burrows
Those who struggle to become a leader, rarely know a clear direction forward for anyone but themselves
Those who struggle to become a leader, rarely know a clear direction forward for anyone but themselves
Re: Bernie and Carols Isuzu fit out.
Back to the future , I have removed the air intake manifold to give easier access to the injector pump . You can see in pic one before I hosed the degreaser off that there was oil present in the 5 ports from the left (cylinders one to five) number six had none .
The small intake thingy on top right is from the compressor , me thinks it has been giving oil to the manifold from there ?? " comments"
Also found the bracket for the throttle has almost wore through another required . The list goes on .
Jon the oil cooler which is under the manifold has signs of electrolysis small pin hole ( check yours ) so that also will be replaced I would say that at some time in its life it ran without coolant .
Bernie .
My mistake that small intake thingy is from the PCV so maybe that needs looking at as well .
The small intake thingy on top right is from the compressor , me thinks it has been giving oil to the manifold from there ?? " comments"
Also found the bracket for the throttle has almost wore through another required . The list goes on .
Jon the oil cooler which is under the manifold has signs of electrolysis small pin hole ( check yours ) so that also will be replaced I would say that at some time in its life it ran without coolant .
Bernie .
My mistake that small intake thingy is from the PCV so maybe that needs looking at as well .
You do not have the required permissions to view the files attached to this post.
Re: Bernie and Carols Isuzu fit out.
A cupple more pics first is the oil cooler cover you can see clearly the electrolysis .
The second is the timing marks on the fuel injector they seem to be a smidgen out .
Jon can you check in your paper work how to adjust that please when you get time that is .
All three of the timing marks on the crankshaft camshaft and idler gear are lined up
Bernie . Not easy to see but they all do line up .
The second is the timing marks on the fuel injector they seem to be a smidgen out .
Jon can you check in your paper work how to adjust that please when you get time that is .
All three of the timing marks on the crankshaft camshaft and idler gear are lined up
Bernie . Not easy to see but they all do line up .
You do not have the required permissions to view the files attached to this post.